I am looking to remove the rear valance only V8 R AWD as I plan to fit the SVR valance and diffuser.
The diffuser comes off easily, but does anyone have instruction to remove valance. Do the parking sensors un plug and come away with the valance or do I need to take the painted bumper off to get to connectors?
Thanks in advance for any help
Best regards
Andrew
Removal of rear valance housing parking sensors
I can send you the Topix file, but I need to know your car.
If you put your make/model i.e Coupé/vert in your signature it helps.
If you put your make/model i.e Coupé/vert in your signature it helps.
2016MY V8R IRR
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
Tel
Would it be better if I sent you the VIN number via DM?
I would be really pleased if you could get me the topix instructions
Many thanks
Andrew
Would it be better if I sent you the VIN number via DM?
I would be really pleased if you could get me the topix instructions
Many thanks
Andrew
MY 2018 V8R AWD Convertible
Ammonite Grey / Black Leather
Modifications:
SVR Bonnet Vents
Flat Bottomed Steering Wheel
Jaguar Aluminium Paddles
Ammonite Grey / Black Leather
Modifications:
SVR Bonnet Vents
Flat Bottomed Steering Wheel
Jaguar Aluminium Paddles
-
- Posts: 1949
- Joined: Sat Apr 15, 2017 8:37 pm
I have removed and replaced my rear bumper cover a couple of times. Manual section 501-19
Fairly simple process of undoing the various fixings across the upper and lower edges. First remove the black loadspace trim at the top edge (where the washer fluid is filled) remove wheel arch liners and using a very long socket extension the 2 bumper to wing fixings on each side. These are horrible to access.. Few other clips to pull apart as you work from the sides to the centre
Lights unclip when you remove cover, but be careful of all sorts of other electrics inside the bumper cover
It's a typical ungainly piece of plastic and easily scratched so rugs on ground and unless brave 2 people to pull it off
Firt time is an hour job, second 15 minutes
Fairly simple process of undoing the various fixings across the upper and lower edges. First remove the black loadspace trim at the top edge (where the washer fluid is filled) remove wheel arch liners and using a very long socket extension the 2 bumper to wing fixings on each side. These are horrible to access.. Few other clips to pull apart as you work from the sides to the centre
Lights unclip when you remove cover, but be careful of all sorts of other electrics inside the bumper cover
It's a typical ungainly piece of plastic and easily scratched so rugs on ground and unless brave 2 people to pull it off
Firt time is an hour job, second 15 minutes
2014 MY 3.0 V6S Roadster
Subtle enhancements to create the car I wanted from SVR nose cone, 400 series side skirts & customised 'design' rear bumper, to heated SVR steering wheel and more
Subtle enhancements to create the car I wanted from SVR nose cone, 400 series side skirts & customised 'design' rear bumper, to heated SVR steering wheel and more
Spot on - No, don't need your VIN I have all the documents to hand.
I'll PM you, that plus cj10jeepers instructions should see you good.
2016MY V8R IRR
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
...looks worse than it is...honestly
2016MY V8R IRR
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
ITG Maxogen Cold air intake kit
Billet OBD lock
Forged lightweight Blades
Full custom Xpel Ultimate PPF wrap
Piano Black badges
17mm MST Hubcentrics
Smarttop remote
Black exhaust tips
Porterfield RS-4 Carbon Kevlar pads
Mich PS4S's
+ more
Thanks Terry
Looks like I need to take the complete bumper off. I was hoping to just take the valance and diffuser off:-)
Thanks for sending.
Regards
Andrew
Looks like I need to take the complete bumper off. I was hoping to just take the valance and diffuser off:-)
Thanks for sending.
Regards
Andrew
MY 2018 V8R AWD Convertible
Ammonite Grey / Black Leather
Modifications:
SVR Bonnet Vents
Flat Bottomed Steering Wheel
Jaguar Aluminium Paddles
Ammonite Grey / Black Leather
Modifications:
SVR Bonnet Vents
Flat Bottomed Steering Wheel
Jaguar Aluminium Paddles
-
- You may also be interested in...
- Replies
- Views
- Last post
-
- 4 Replies
- 414 Views
-
Last post by shatnersbassoon
-
- 12 Replies
- 2761 Views
-
Last post by cj10jeeper
-
- 0 Replies
- 5305 Views
-
Last post by paddy1000111
-
- 0 Replies
- 2286 Views
-
Last post by giusemanuel
-
- 15 Replies
- 546 Views
-
Last post by Moss